Lencore n.Form: MPI-6 Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Příslušenství komunikace Lencore n.Form: MPI-6. Lencore n.Form: MPI-6 User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 17
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
MPI-6 User Manual
Version 1.1
Zobrazit stránku 0
1 2 3 4 5 6 ... 16 17

Shrnutí obsahu

Strany 1 - MPI-6 User Manual

MPI-6 User ManualVersion 1.1

Strany 2

section 22.5 | mic paging 81. Connect a MIC to Lencore’s MIC pre-amp.2. Connect the audio output of the MIC pre-amp to one of the six audio inputs of

Strany 3 - safety instructions

section 22.5 | RAMP paging9Use with a RAMP:Note: DIP switch 5 on the RAMP must be down.Relay outputs 1-8 can be used to trigger RAMP messages to repla

Strany 4 - Link to product page

section 22.6 | relay outputs10Paging Priorities:MIC all-call over phone.MIC all-call over MIC zone.Phone all-call over MIC zone.Last MIC zone triggere

Strany 5 - 1.1

section 22.7 | audio inputsAudio input adjustment (figure 6) – There are six audio input adjustments – one for each audio input. Using a flat-blade s

Strany 6 - 2.1

section 22.8 | audio input adjustment12Other:Service button (figure 2)-Pressing the Service button plays a short audio clip over the audio source 6 li

Strany 7 - 2.2

section 22.8 | audio input adjustment13Internal speaker source select (figure 1)-The rotary selector switch can select the audio source to play over t

Strany 8 - 2.3

section 22.9 | overall I/O14figure 7 - overall I/O

Strany 9 - 2.4

The information contained herein is proprietary to Lencore Acoustics Corp. and copyright protected. No part of this manual can be copied, used or dis

Strany 10 - 2.5

MPI-6section 0 page 1section 1 page 2 IMPORTANT SAFETY INSTRUCTIONS & PRECAUTIONS INTRODUCTION - ABOUT MPI-61.1 basic information on MPI-6page

Strany 11 - 2.5

Follow all instructions.Do not use this equipment near water.Clean only with dry cloth.Do not block any ventilation openings. Install in accordance w

Strany 12 - 2.6

introductionMPI-62The MPI-6 is Lencore’s music and page interface to be used for Emerald and iNET systems. The MPI-6 includes an analog

Strany 13 - 2.7

section 11.1 | components 3• Power LED.• Status LED.• Input level LEDs for music and paging (RCA inputs only – not phone).• Neuron status LEDs.• Rela

Strany 14 - 2.8

section 22.1 | inputs and outputs 4• Power input.• POTS line input (RJ11).• Ground 2-pos terminal block (screw terminals).• iLON input 2-pos terminal

Strany 15

section 22.2| LEDs and switches 5Power – solid when board is poweredStatus – blinks every 8 seconds and solid when paging. Solid when an IR remote bu

Strany 16 - 2.9

section 22.3 | operation 6figure 1- overall MPI-6Plug the power adapter into the MPI. The Power LED will be on and solid while the Status LED will bl

Strany 17

section 22.4| phone paging 71. Plug the analog phone line (RJ11) into the MPI Phone input.2. Dial the extension of the phone line. The Status LED wil

Komentáře k této Příručce

Žádné komentáře